VQFREM 400 S

VQFREM 400 S are vector control frequency converters using HDDis of the latest generation. They have been specially designed for the most difficult technical drives applications with induction or synchronous motors with permanent magnets supplied by 3 × 400 V, motor power up to 75 kW. VQFREM 400 S frequency converters are characterized by high dynamism of system and high overload factor. They are designed booth for open and closed systems. VQFREM 400 S basic option standardly contains software which permits energetic input power optimalization, accurate speed control and motor torque control. The main benefit of VQFREM 400 S frequency converters in comparison with VQFREM 400 is the ability of high-speed motors control. Output frequency of 3000 Hz can be reached. It enables special motors regulation to 180.000 revolutions per minute.

VQFREM 400 S family in all versions is compliant with EU standards and regulations:

Contents:

VQFREM basic

• real time function: enables precise monitoring of converter operation in time, e.g. fault specification
• built-in control panel "CP": the panel contains alphanumeric 4 x 20 characters display and 9-buttons keypad. The display displays operating instructions in Slovak language and English and the keypad is used for parameters setting and changing
• RI suppression filter class A1 (according to STN EN 61800-3)
• commutating reactor "CR": integrated in the frequency converter circuit to reduce current harmonic distortion of power supply. It lengthens the operating life of power capacitors of a converter.
• inputs: 3 analogue inputs, 6 programmable binary inputs
• outputs: 2 analogue current outputs: 0 ÷ 20 mA (4 ÷ 20 mA) for output frequency (current) indication
• 3 programmable output relays 230 V / 3 A (e.g. fault, READY...)
• two sets of adjusting parameters
• setting of desired value: binary 8 speeds, reverse, reset, analogue signal 0 ÷ 10 V, 2 ÷ 10 V, or 0 ÷ 20 mA, 4 ÷ 20 mA, potentiometer, external motor - potentiometer
• adjustable acceleration time (ramp-up time) and deceleration time (ramp-down time)
• PID process regulator (also reversal function)
• aic parking of a converter - if analogue input signal is sufficient and the regulation uses PI process regulator
• energetic input power optimalization
• fault history (the converter remembers the latest 10 faults)
• U/f characteristic for constant and variable motor torque
• motor braking - 3 braking modes
• measurement of: f_OUT, RPM, U_OUT, U_IN, I_OUT, analogue input
• modern type SkiiP, SkiiM, IPM - semiconductors, which have lower losses than IGBT. They incorporate an input rectifier and an output inverter and provide complex converter protection (protection against short circuit between output phases, ground faults, overtemperature).

Optional accessories

• EMC (Electromagnetic compatibility):

  PROFIBUS DP	- Vonsch option module PROFIBUS DP enables to control maximum of 99 frequency converters. ID Number: 077 B HEX
  LON	- enables frequency converter control via electric power network
  GSM	- enables frequency converter control via telecommunication network
  Ethernet	- enables frequency converter operation in industrial networks (communication network for industrial applications)

• external wall control panel "EWCP": it should be wall mounted (the doors of electrical enclosure). EWCP uses RS 422 system to communicate with the converter and can be mounted up to 100m from the converter. The panel contains 4-lines alphanumeric display (displaying in Slovak and English) and 9-buttons keypad.
• external manual control panel "EMCP": it is designed for manual control of a converter. EMCP enables parameters indication and setting. In addition, it enables that the parameters can be copied from one converter to another. The rest holds as for EWCP.
• external door control panel "EDCP": it should be mounted on the doors of electrical enclosure. The panel is mounted on the front doors of electrical enclosure so as only membranous keypad is visible and reachable from outside of electrical enclosure. IP55 protection is ensured by this solution. The rest holds as for EWCP.
• output reactor "OR1" (filter du/dt): it eliminates cable capacitance on frequency converter. Output reactor should be connected to the output terminals U, V, W.
• sinusoidal output filter "SF1" - ensures converter output voltage to reach the desired sine waveform. If there is minimum radio interference emission demand (e.g. theatres), screened interconnecting cables between a converter and a motor do not have to be used when using sinusoidal output filter. Sinusoidal output filter completely eliminates overvoltage spikes on output (motor) terminals. It can be connected directly to the output terminals of frequency converter. If using sinusoidal output filter, it is necessary to set sampling frequency (parameter 9.1.1) rating from 5 ÷ 10 kHz and frequency converter cannot operate in vector control mode.
• higher degree of protection - e.g. IP55, IP66 (frequency converter is built-in electrical enclosure)